As well as images, articles and reviews for most modern and vintage record players, we have a friendly forum where visitors can share their knowledge, and a huge archive of owners manuals, service manuals, schematics and brochures.
Operator Manual Bv 300 Philips
We export and wholesale superb quality Philips BV-300 ultrasound which comes with commendable features like tri-Mode 9"/6"/4" Image Intensifier, CCD Camera, 200 Digital Image Storage, Dual 17" Hi-resolution Monitors With Cart, Matrix Camera 8"x10" Format, Fixed X-ray Tube Certified, BV300 Operators Manuals and Patient Data Keypad. Apart from these it has 200 frames memory, hard copy device and laser alignment. We offer philips BV-300 at competitive prices.
To remove the disposable batteries, see the battery installation section.ComplianceThis product complies with the radio interference requirements of the European Community.Hereby, TP Vision Europe B.V. declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can find the Declaration of Conformity on www.p4c.philips.comFCC Statement :Caution FCC and IC Statement for Users (the USA and Canada only)NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Precautions Concerning BatteryWhen the Remote Control is not to be used for a long time (more than a month), remove the battery from the Remote Control to prevent it from leaking.if(typeof ez_ad_units!='undefined')ez_ad_units.push([[300,250],'manuals_plus-mobile-leaderboard-2','ezslot_17',708,'0','0']);__ez_fad_position('div-gpt-ad-manuals_plus-mobile-leaderboard-2-0');If the batteries leak, wipe away the leakage inside the battery compartment and replace the batteries with new ones.Do not use any batteries other than those specified.Do not heat or disassemble batteries.Never throw them in fire or water.Do not carry or store batteries with other metallic objects. Doing so could cause batteries to short circuit, leak or explode.Never recharge a battery unless it is confirmed to be a rechargeable type.ConnectThis section helps you connect your Soundbar to aN and other devices.For information about the basic connections of your Soundbar and accessories, see the quick start guide.NoteFor identification and supply ratings, refer to the type plate at the back or bottom of the product.Before you make or change any connections make sure that all devices are disconnected from the power outlet.PlacementPlace the subwoofer at least 1 meter (3 feet) away from your Soundbar, and ten centimeters away from the wall.For best results, place your subwoofer as shown below.if(typeof ez_ad_units!='undefined')ez_ad_units.push([[970,90],'manuals_plus-box-4','ezslot_10',103,'0','0']);__ez_fad_position('div-gpt-ad-manuals_plus-box-4-0');Connect the audio from TV and other devicesConnect to HDMI (ARC) SocketSome 4K HDR TVs require the HDMI input or picture settings to be set for HDR content reception. For further setup details on HDR display. please refer to the instruction manual of your TV.Your Soundbar supports HDMI with Audio Return Channel (MC). If your TV is HDMI MC compliant, you can hear the TV audio through your Soundbar by using a single HDMI cable.
NoteYour TV must staopect the HDMI-CEC and ARC functions. HOMICEC and MC must be set to OnThe setting method of HC*11-CEC and MC may offer depending on the IV. For data about MC futon please refer to your TV ChNTIWS manualOnly HDMI 1.9 compaubk cables can support the ARC functionConnect to Optical SocketUsing an optical cable(not included), connect the OPTICAL connector on your Soundbar to the OPTICAL OUT connector on the TV or other devices.
SoundNo sound from Soundbar speakers.Conned the audio cable from your Soundbar to yourTV or other devices.Reset your Soundbar to its factory settings.On the remote control, select the correct audio input.Make sure that the Soundbar is not muted.Distorted sound or echo. If you play audio from through the Soundbar, make sure that theTV is muted.BluetoothA device cannot connect with the Soundbar.The device does not support the compatible profiles required for the SoundbarYou have not enabled the Bluetooth function of the device. See the user manual of the device on how to enable the function.The device is not correctly connected. Conned the device correctly (see Bluetooth Operation on page 13)The Soundbar is already connected with another Bluetooth device. Disconnect the connected device, then try again.The quality of audio play from a connected Bluetooth device is poor. 2ff7e9595c
Коментарі